This is a Blade 400 3D Edit of the Original Blade 400 3D.  This is more in like a real Blade 400, It has the correct specs as a Real Blade 400, and it also has the new radio setup that you can find on Horizon Hobby's site.  Also, just as a side note this has 1 upgrade on it that I had to do to get the tail to work right, It has a Spektrum DSP75 Digital servo on the tail.  With at least a digital servo and the G110 in "DS Mode" the tail will work much better on your Blade 400.

In order to use this Blade 400 you must first download this. Then you can use my edit.

*Note: after you download this rename the .zip to .rfx, Happy Flying.

*Note: You need to have the Blade 400 3D or Blade 400 3D v2 to use this edit.  The Blade 400 can be downloaded here. The Blade 400 3D v2 can be downloaded here.

*Note: After you download this file you need to Re-Start RealFlight in-order for it to work properly

This is an edit of the Blade 400 3D,  It Still has the stock motor, but now it has some Upgrades like, CY Radix 325's Main Rotor Blades, An Align RCE-BL35X ESC , The Hitec HS-5065MG's on the Cyclic, and a Hitec HSG-5083MG on the tail.  It also now has a Futaba GY-401 Gyro, an Align High Power 20C 3S LiPo, and it has a Stiffer head to make it fly like it has a Simulated Aluminum Head.  This also has a modified radio setup based off of the new Horizon Hobby setup.  It also has all of the correct weights and Specs now.

*Note: after you download this rename the .zip to .rfx, Happy Flying.

*Note: You need to have the Blade 400 3D or Blade 400 3D v2 to use this edit.  The Blade 400 can be downloaded here. The Blade 400 3D v2 can be downloaded here.

*Note: After you download this file you need to Re-Start RealFlight in-order for it to work properly

The flybarless version of the Dominion 3D 90 offers the maximum in 3D potential.  Powered by an O.S. Engines .90 HZ-PS 3D with the PD-08 pump, this Dominion 3D 90  is the right choice for practicing intense unlimited 3D aerobatics.  Removing the flybar allows for a more efficient head due to reduced mass, leading to faster cyclic response, and with the Simulated "Mikado V-Bar" system it's awesome for hard 3D flight.

*Note: after you download this rename the .zip to .rfx, Happy Flying.

*Note: After you download this file you need to Re-Start RealFlight in-order for it to work properly.

*Disclaimer: The "Mikado V-Bar" used in this heli, is not based on the real one. I have never used one but this is how I think it might fly.

This is "Toad's" Align Trex 450S or "The Beast" as it's called.

This is a Align Trex 450S that has been setup to fly like "Spasticatedtoad's" "The Beast".

This Heli Has an Align High Power 20C 11.1V 2100mAh 3S LiPo battery that has a Simulated LVC in the Sim. The Rotor Blades are powered by an Align 430X 3,550kV Motor (with a 13T Pinion Gear and 150T Main Drive Gear), and uses an Align RCE-BL35X ESC.

The Cyclic Servos are all Hitech HS-65HB Servos Running at their correct 6V Speeds (.11).  The Tail Servo is a Hitech HSG-5084MG Servo (.05).

The Gyro is a Futaba GY-401 Heading Hold Gyro.

All Servo Speeds, Motor Gearing, and Throttle/Pitch Curves are set how the real "Beast" is set up.

In order to use this Trex 450S you must first download this. Then you can use my edit.

*Note: after you download this rename the .zip to .rfx, Happy Flying.

*Note: You need to have the Align Trex 450 SE V2 G45 to use this color scheme.  The Align Trex 450 SE V2 G45 can be downloaded here.

*Note: After you download this file you need to Re-Start RealFlight in-order for it to work properly.